Files
TeslaRel410/emulator/render-bridge/logs/059-dosbox.txt
T
CydandClaude Fable 5 f2687a3146 BT410 5.3.72: the fault caught in the act; the inside view gets its cockpit
VPX_PF_WATCH (fork, cpu/paging.cpp): on a guest page fault at the watched
linear address, dump guest registers, the last 64 serial RX deliveries with
guest cs:eip at each, the code bytes at the faulting EIP and the stack top.
serialnamedpipe's doReceive feeds the ring.  Armed in podrun.sh and
launch_pod.ps1.

The first catch decoded the residual fault completely: CS:EIP 00FF:000066D4
in the DPMI host, EBX = F000CA60 -- an IVT entry read as a dword, segment
F000 offset CA60, a BIOS default interrupt handler -- and the faulting access
is [EBX+0x3004], whose 0x80000000 segment-base wrap gives exactly cr2
7000FA64.  The host probes a word 0x3004 bytes past a real-mode vector value
treated as a flat pointer: harmless for its own low-memory handlers, a fault
for BIOS F000:xxxx defaults.  The serial ring shows a steady 1-byte/1-3ms
vRIO stream with nothing special at the fault -- the stream determines which
vectors get walked, not the crash itself.  The 0x3004 appears nowhere in
DPMI32VM.OVL or 32RTM.EXE as an immediate, so the probe now also dumps code
bytes at EIP; faulthunt.sh loops runs until the next catch.

Shipped baseline streak: 4/4 clean -- consistent with exposure, not yet
discriminating.

The inside view now loads the COCKPIT skeleton: the fleet-wide X-variant
naming convention (MAD->MAX etc., all 64 skeletons present) selects the same
25-joint chain with a single object -- max_cop.bgf, the MAX_COP canopy shell
with the PUNCH-texel windows from the capture forensics.  The donor names the
same mechanism from the decomp side (inside = SkeletonType_A with '_cop'
selection).  Fallback to the body skeleton when no X file exists.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
2026-07-29 18:09:22 -05:00

84 lines
4.8 KiB
Plaintext

LOG: Early LOG Init complete
LOG: CONFIG: Loaded config file: C:/VWE/TeslaRel410/emulator/render-bridge/pod_render_rec.conf
LOG: DOSBox-X's working directory: C:\VWE\TeslaRel410\emulator\src\src
LOG: Logging init: beginning logging proper. This is the end of the early init logging
LOG: Logging: No logfile was given. All further logging will be discarded.
LOG: DOSBox-X version 2026.06.02 Commit d75a57c (MinGW SDL2 64-bit)
LOG: Prevent capture: 0
LOG: SDL: version 2.32.10, Video windows, Audio directsound
LOG: EXPERIMENTAL: Debugger enabled for MinGW build, DOSBox-X crashes depending on the terminal software you use. Launching from command prompt (cmd.exe) is recommended.
LOG: Windows keyboard layout ID is 0x0409
LOG: Host keyboard layout is now us (US English)
LOG: Mapper keyboard layout is now us (US English)
LOG: SDL2 reports desktop display mode 3440 x 1440
LOG: OpenGL Version : 4.6.0 NVIDIA 610.47
LOG: Configured windowposition: -
LOG: SDL: Current window pixel format: SDL_PIXELFORMAT_RGB888
LOG: SDL: You are running in 24 bpp mode, this will slow down things!
LOG: Releasing keyboard
LOG: SDL: Windows 11 round corners will be disabled.
LOG: Screen report: Method 'Win98base' (3440.000 x 1440.000 pixels) at (0.000 x 0.000) (910.167 x 381.000 mm) (35.833 x 15.000 in) (96.000 x 96.000 DPI)
LOG: ISA BCLK: 8333333.333Hz (25000000/3)
LOG: monopal: green,
LOG: Active save slot: 1 [Empty]
LOG: USING AVI+ZMBV
LOG: Pentium CMPXCHG8B emulation is enabled
LOG: Max 1073741824 sz 32768
LOG: Final 32768
LOG: Final arrangement: Below 4GB = 32768KB, Above 4GB = 0KB
LOG: VPXLOG: fifosock listening on 127.0.0.1:8621
LOG: VPXLOG: live render backend started
LOG: VPXLOG: base 0x150 respond=1 handshakes=3 log='C:\Users\cyd\AppData\Local/Temp/vwe-pod/vpxresp.txt'
LOG: MIDI:Opened device:win32
LOG: mic_input: Selected microphone device: Microphone (Steam Streaming Microphone)
LOG: One joystick reported, initializing with 4axis
LOG: Using joystick Xbox One Controller with 6 axes, 16 buttons and 1 hat(s)
LOG: VOODOO LFB now at d0000000
LOG: Serial1: BASE 3f8h
LOG: Serial1: namedpipe client of \\.\pipe\vrio (poll 0.10ms burst x16)
LOG: Serial1: namedpipe connected to \\.\pipe\vrio
LOG: Serial2: BASE 2f8h
LOG: Serial2: namedpipe client of \\.\pipe\vplasma (poll 1.00ms burst x1)
LOG: Serial2: namedpipe connected to \\.\pipe\vplasma
LOG: Serial3: BASE 3e8h
LOG: Serial: port 3 will write to file C:\VWE\TeslaRel410\emulator\render-bridge\podlog.txt
LOG: Parallel1: BASE 378h
LOG: MPU-401 Registering I/O ports as if IBM PC MPU-401 at base 330h
LOG: Memory I/O complexity optimization enabled aka option 'memory io optimization 1'. If the game or demo is unable to draw to the screen properly, set the option to false.
LOG: The 'scanline render on demand' option is available and may provide a modest boost in video render performance if set to true.
LOG: Allocated APM BIOS pm entry point at f000:ce40
LOG: Writing code to fce40
LOG: Writing code to fce60
LOG: Windows: IID_ITaskbarList3 is available
LOG: ISA Plug & Play BIOS enabled
LOG: VGA ROM BIOS init callback
LOG: pixratio 1.000, dw false, dh false
LOG: Aspect ratio: 640 x 480 xToY=1.333 yToX=0.750
LOG: WARNING: No translation support (to host) for code page 0
LOG: DOS keyboard layout loaded with main language code US for layout us
LOG: XMS: 50 handles allocated for use by the DOS environment
LOG: EMS page frame at 0xe000-0xefff
LOG: COMMAND.COM env size: 720 bytes
LOG: COMMAND.COM environment block: 0x0701 sz=0x002d
LOG: COMMAND.COM main body (PSP): 0x072f sz=0x009a
LOG: COMMAND.COM stack: 0x0749
LOG: pixratio 1.350, dw false, dh false
LOG: Aspect ratio: 720 x 540 xToY=1.333 yToX=0.750
LOG: SHELL:Redirect output to COM3
LOG: VPXLOG: fifosock client connected
VPX lights@f1: type6=0 typeE=0 decoded=0 dir=0 amb(0.00,0.00,0.00)
LOG: 420998823 ERROR MOUSE:Unhandled videomode 79 on reset
LOG: pixratio 1.000, dw false, dh false
LOG: Aspect ratio: 640 x 480 xToY=1.333 yToX=0.750
VPX lightnode t=6 nb=52: [8]00000000/0 [12]00000000/0 [16]00000001/1.4013e-45 [20]3f800000/1 [24]3f800000/1 [28]3f800000/1 [32]64078678/1e+22 [36]64078678/1e+22 [40]00000000/0 [44]3e25a5b9/0.161765 [48]ffffffff/nan
VPX lights@f121: type6=2 typeE=6 decoded=2 dir=1 amb(0.55,0.50,0.65)
L0 dir(0.11,0.77,0.63) col(1.10,0.90,1.00)
VPX lights@f241: type6=2 typeE=6 decoded=2 dir=1 amb(0.55,0.50,0.65)
L0 dir(0.11,0.77,0.63) col(1.10,0.90,1.00)
VPX lights@f361: type6=2 typeE=9 decoded=2 dir=1 amb(0.55,0.50,0.65)
L0 dir(0.11,0.77,0.63) col(1.10,0.90,1.00)
VPX lights@f481: type6=2 typeE=10 decoded=2 dir=1 amb(0.55,0.50,0.65)
L0 dir(0.11,0.77,0.63) col(1.10,0.90,1.00)
VPX lights@f601: type6=2 typeE=10 decoded=2 dir=1 amb(0.55,0.50,0.65)
L0 dir(0.11,0.77,0.63) col(1.10,0.90,1.00)